gas services in Richmond BC

Fixing A Leaky Faucet

 

Drip. Drip. Drip. 

The faucet is leaking. Aside from it being annoying and irritating, it’s also wasting water. As it continues to waste more water, the water bill also gets higher. Shaul’s is a local plumbing contractor in Richmond BC that provides quality plumbing services in Richmond BC and we can help you with your problem of a leaky faucet.

As a trusted plumbing and heating contractor in Richmond BC, Shaul’s offers professional plumbing and heating services in Richmond BC for your needs. We also are available anytime for emergencies.

Fortunately, it’s a simple task to fix your leaky faucet if you have the following needed materials.

  • Screwdriver
  • White vinegar
  • Scouring pad
  • Adjustable wrench
  • Plumber’s grease
  • Replacement Kit

The four common types of faucets are Compression, Ball, Cartridge, and Ceramic Disk. Whatever faucet you have to fix, you should do the following before starting the job.

  • Turn off the water to the faucet from under the sink. If you don’t, you’ll end up with a flooded bathroom or kitchen. Do a clockwise turn to shut off the water.
  • Cover the sink drain with any stopper to avoid dropping the small parts down the drain.

Identify the kind of faucet you have, and then you can begin repairing it. Here’s how to fix leaky faucets.

Compression Faucet

  • heating contractor in Richmond BCPry off the decorative cap.
  • Unscrew the handle and pull it off.
  • Use a wrench to unscrew the packing nut or stem.
  • Pull out the stem, remove and replace the seat washer held by a brass screw.
  • Coat the washer replacement with plumber’s grease.
  • If the handles are leaky, replace the O-ring with a size that exactly matches the old one.
  • Reassemble the faucet in reverse order when you took it apart.

Ball Faucet

  • Buy a replacement kit in the plumbing section of repair shops.
  • Unscrew and remove the handle.
  • Remove the cap and collar using pliers.
  • With the help of a tool included in the replacement kit, remove the faucet cam, the cam washer, and the ball.
  • Reach into the faucet and remove the inlet seals and springs using a needle-nose plier.
  • Cut off the O-rings and replace them with new ones coated in plumber’s grease.
  • Reassemble the faucet by installing new springs, valve seats, and cam washers which should be included in the kit.

Cartridge Faucet

  • Pry off the decorative cap.
  • Unscrew the handle, tilt it backward, and pull it off.
  • Using a needle-nose plier, remove the threaded retaining clip that holds the cartridge in place.
  • Pull the cartridge straight up.
  • Remove the faucet spout.
  • Using a utility knife, cut off the O-rings and replace them with new ones coated in plumber’s grease.
  • When you took it apart, reassemble the faucet in reverse order.

Ceramic Faucetplumbing services in Richmond BC

  • Unscrew and lift off the handle.
  • Remove the escutcheon cap.
  • Unscrew and lift out the cylinder, then clean it with white vinegar and a scouring pad. Replace the cylinder if it’s damaged.
  • Pry out the neoprene seals using a screwdriver.
  • If the seals look pitted or worn, replace them.
  • Reassemble the faucet and very slowly turn the water back on.

Most faucets can live up to 10 years before deteriorating. But you don’t have to wait that long before you decide to repair or replace them. If you’re looking for a plumbing and gas contractor in Richmond BC, Shaul’s is the one. We offer quality plumbing and gas services in Richmond BC. You can contact us anytime to have your faucets checked.